Holy moly is that a big heatsink.
Holy moly is that a big heatsink.
Obviously a homebuilt watercooling rig is going to be way better than AIOs, but it requires extensive maintenance. It's water. Stuff will grow in there. It evaporates. Joints loosen over time and could end up shooting water all over your $6000 workstation.
To me, it's not worth it. Threadripper requires a big heatsink. So be it.
Water cooled PCs do pretty look cool though.
Converting water to steam takes about (from the top of my head) 5x more energy than it takes to increase it by one degree. I imagine the coolant used in these heat sinks is at least this efficient, if not more, and is something that evaporates well below 100°C.
If heat sinks were like using cars and roads to transport people. A water cooled setup would be like expanding the size of the roads to increase the number of cars that can transport people. While those heat pipe coolers are like replacing cars with trains, so you can do a lot more the same amount of space.
I think this greatly underestimates the potential of evaporative cooling. The "specific heat of water" is 1 calorie/gram °C --- that is, one calorie can heat one gram of water by one degree Celsius if no phase change is involved. The "heat of vaporization of water" is more than 500 calorie/gram at 100°C. That is, the energy necessary to convert a given quantity of liquid water from just below boiling to steam is not 5x the energy necessary to raise that amount of water 1°C, but 500x! You are probably remembering that this is 5x the energy necessary to take liquid water all the way from 0°C (almost frozen) to 100°C (almost boiling).
The pump does not need to have air flow to do its job and airflow is what carries noise. The water just has to be able to flow through the loop, pretty much any rate of flow will be pushing enough water to move heat away. If you hold your hand to a water block with the pump turned off, let it warm up and turn it on, it feels like the water is going over your hand. The temperature change is immediate. If you turn off the pump while the CPU is running, the temperature will rise a few degrees each second. Once the pump goes on the temperature drops down immediately.
There is no reason that the liquid should evaporate unless there are leaks and joints don't necessarily loosen over time. Also leaks are unlikely to manifest in something bursting and water spraying, even if you had enough pressure from your pump, which you don't (a pump can probably only pump water four or five feet higher than the pump itself, even if it is more powerful than the loop needs).
I have never had to maintain or fix something after it is together. Use vinyl tubing from the hardware store over the barbs and use small pipe clamps on top of them.
Was fine. I fixed it, refilled it and posted it back! Still running 5 years later.
But I do go a little more paranoid and insist on more expensive silicone tubing(some $$$). Fits nicer, feels nicer, less concern over perishing.
You can have higher tech radiators with better fins along with better fans and airflow modelling etc of course.
But it is always better if there is more of it.
But also depends on where in the world you live and what the climate is like.
For the normal desktop cpus, I like the Dark Rock better. Cooling is the same as noctua but was quieter for me.
I should note it's WAY louder than I thought it'd be and it's made getting to my NVME drives a bit difficult.
I didn't do much research beyond "best analog HSF vs watercoolers" and when it showed up I couldn't believe how big it was.
Honestly the best bit though was the piece of mind that I don't have liquid inside my computer anymore. The idea of the pump leaking down onto my GPUs when I'm not around was stressful.
Building an open water loop would be awesome for the GPU cooling. I just can't justify the expense.
Air cooling excels mostly everywhere else.
Neither can cool your system to below ambient room temperature.
Ultimately, you want more surface area to blow air across to cool things. "Water cooling" is really "water transports heat to fins for cooling". Just a bigger version of the heatpipe really.
If the fins are not better suited to airflow cooling then it won't help you.
The AIO radiators don't add that much more fin area than a good air cooler if at all. But you can put them somewhere outside the otherwise warm case if that helps. Maybe if you live some cold and your desk is just right you could dangle it out the window?
Also, for the noise conscious, two(often on the 280 AIOs) or more fans "beat frequency" is a thing. Also why I don't like "push-pull" configs on air coolers.