I particularly like the Tech Tuesday videos, partly because Calvin Jones is so fun to watch (although he's not just a pretty face [2]), but also because, for example, this is the first explanation i ever heard of how hydraulic brakes self-centre that actually makes sense:
https://www.youtube.com/watch?v=vQXFFgRButo&vl=fr
[2] https://www.probma.org/blog/calvin-jones-more-neednt-be-said
I suspect an organised person could learn much more efficiently than this.
One pitfall to watch out for is that in cycling, everyone has their opinions, which they will proclaim as absolute truth. If you're just following one person, it can be hard to distinguish universally agreed common sense from opinion.
i built my own bike without help when i was a teenager.
there aren't that many parts and your main struggle will be to decide what from the different options for each part to choose.
there are different gear and brake systems to choose from, and if you don't know what's better for you, your bikeshop can advise you.
for my bike i used mostly standard parts, that is the common stuff found on every other bike and available in every shop. the only thing where i splurged is a good leather sattle from brooks.
Car/motorcycle/bike maintenance - it's always better to have someone who has a fair bit more experience than you sitting in your shed drinking your beer and eating your pizza while you do your own work.
Depends, I guess, on where you're starting from. Some people know how hard you should/shouldn't push on a 10mm spanner or a 6mm allen key. That kind of "matter of feel" comes from someone who's already got it showing you and letting you feel it, or from a trail of stripped bolts and/or crashes where your brakes failed or fell off 'cause you didn't torque them up tight enough...
In person expertise is not essential, but I do think launching into repairing your own brakes is perhaps the _worst_ example of something you should learn from Youtube... (Although adjusting bicycle brake cables is not nearly as bad an example as, say, removing callipers and swapping out brake pads on a motorcycle...)
If you can find someone to help teach you, it's well worth the pizza and beer it usually costs...
I've also totally stripped and rebuilt several VW Beetle motors (and a Kombi one), a 13B Mazda rotary (which ended up in the 72 Beetle eventually), and my Ducati Monster 900 (engine/gearbox). I own one motorcycle that needs a new top end rebuild every 10,000km (A Cagiva Mito 125cc two stroke). I've done the desmo valve clearances on that Ducati every 20,000km since 1999 (it's got over 320,000km on it now.)
So I'm not particularly scared of most mechanical things (I'm more put off by the pains of a 50year old body crouching down next to a motorcycle in the cold these days than worried about working on the mechanical stuff...)
But I _am_ acutely aware that many (most?) people didn't have fathers who taught them how to work on cars/lawnmowers when they were 7 or 8 years old, and have no clue at all how tight fasteners should be or much force you can put on them before starting to worry about whether you need to start checking if you've missed the lock nut or split pin. People who have no feel for whats "About right" for a 10mm fastener compared to a 17mm or 32mm one. People who don't read a torque spec of 10Nm for an M6 fastener and realise "Oooh, that's not very tight, must be a stainless fastener into a soft-ish allow..."
I _strongly_ stand by my advice of making a more experienced friend and having them oversee things and be there for when you're not sure if you're doing things right.
So it’s possible to perform a new mechanical operation without a personal guide present?
For VW’s Haines is definitely better. I had both for my 64. No CV joints on that one. Swing axel.
And static timing. Which is an example of trial and error and eyeballing. That’s essentially how the Haines described it.
Oh sure.
But I reckon learning the 4th, 5th, 100th new thing is _way_ less learning curve than learning the 1st, 2nd, and 3rd things. It's that early steep learning curve of all the assumed knowledge that Haines/Chilton/Ducati workshop manuals where a workshop buddy is hugely beneficial.
Happy to disagree on this. But I also will continue to recommend finding a more experienced person to help out when you're starting out, and will regularly offer to be "that guy" for people who show interest.
(Also, didn't the '64 still have inboard CV joints? My '69 had the "two joint rear end" with CVs up against the transaxle but none at the wheel hubs and the bendy trailing arms (according to most info that means it was probably a '68, but it had a 1969 Australian compliance plate of it :shrug:). The '72 had the four joint rear end.
For VW’s I think model years and features vary by region.
Oh no, I agree there too. It's probably the second best way to learn. (Though for me, I have more of a "read the words and look at the pictures" kind of brain, I'd choose a decently written blog post or manual over video content every time...)
But I _think_ the part of my comment you're pushing back against didn't suggest that Youtube was the worst way to learn - but rather that brakes were that _last_ thing I'd recommend someone starting out learns by themselves on Youtube. (It's entirely possible I didn't write that clearly enough though...)
Start out learning (whether by Youtube or with an experienced person) how to replace light bulbs and fill you windscreen washer fluid and upgrade your stereo, then move on to more safety-critical but low risk things like oil changes, ignition timing, carb/fuel injection service - the sort of things that if you get it wrong make you stop. Leave the things that if you get it wrong you _don't_ stop until you're totally confident you know you are going to get it right.
Brakes are one of the few things I say no to helping friends out with. If they start to work on them while I'm around, that's OK, but if they invite me round to show them how to do it I'll tell them "No, take your brakes to a licensed/insured mechanic."
By trial and error, I mean small scale and safely. Like truing a wheel. Spin, adjust, spin, adjust, spin, adjust...and eventually the wheel is true. That's when it's ok to ride on it.
Brakes and bearings are spin, adjust, spin, adjust too. The difference experience makes is fewer spin, adjust loops to get it right enough to ride on.
The bike I bought at a dealership is just a couple months old and no maintenance work had been done so far.
I am feeling it’s about time for some adjustments (rim brakes are accumulating some leeway now), and thought I could as well replace some parts while at it and start to learn how to put together a fully custom ride (to use the skill in future after I move to a more permanent location).
But if that's your plan, then you'll need tools. Not many. Mostly basic bicycle tools. Not specialized tools for most situations, that's why those tools are specialized.
The tools I'd recommend starting with to keep your bike safe -- these handle everything that occurs day to day. They focus on the wheels.
hex wrenches. so nothing that's loose stays loose.
cheap ones are fine.
I mostly use a set of tee handles bought
from Harbor Freight for about $12. Sometimes
L-shaped hex wrenches for tight spaces.
track pump, it just makes keeping tires properly
inflated easy. Inflation makes a huge difference.
Tires lose significant air in a week.
tire levers.
a patch kit that uses rubber cement.
truing stand - a cheap one from china is more than good
enough. Without a trued wheel, brakes cannot be optimally
adjusted. Trued wheels create a huge ride difference.
Anyone can true a wheel, it just takes time and patience.
spoke wrench. not just for truing wheels but for
insuring spokes are not loose. not-loose is not quite
the same as tight. spokes need the right amount of tension.
the right amount is loose enough to for the wheel not
to run to that side and tight enough for it to stay true
chain lube.
screw driver for adjusting derailleurs if the chain
rubs AND you're not riding cross chained.
Second level tools for bearings. Wheel bearings don't require much attention but can need periodic service. If the wheel moves laterally when the brakes are applied or doesn't spin freely and isn't rubbing, adjust the bearings. magnetic parts cup. when something comes off the bike
that's where it goes. even if it's not magnetic.
especially if its small. It will also find ball bearings
when they are lost.
cone wrenches to adjust wheel bearings. these are just
flat wrenches.
white lithium grease for wheel bearings. don't put it on
your seat post
Everything else is pretty rare - modern cartridge bottom brackets have removed a lot of maintenance and the associated tools. Pick them up when you need them. You need them when a job with the tools you have seems to require a lot of force or not be possible.Lastly, not doing maintenance doesn't make your bike safer. If something requires maintenance and you break it and can't ride, that's safer than not doing required maintenance and going for a ride.
If you're really worried about over-torquing something, you can throw money at it. There are torque-wrench versions of bicycle tools that are used for torque sensitive operations.
Good luck.