It's also amazing how prevalent Ethernet still is, even when wireless is a competitor. The other day I left this comment: http://news.ycombinator.com/item?id=5052448 on HN, because in some circumstances running a cheap ethernet cable from a router to a desk, couch, or other work station can still be a real win, especially given how inexpensive even very long ethernet cables are from Monoprice.com.
They last forever, aren't subject to the level of interference wireless is, and, in many conditions, have faster data transfer speeds. Ethernet is still great.
Someone measured the difference in transmissivity for different materials at 2 and 5 GHz (http://www.ko4bb.com/Manuals/05)_GPS_Timing/E10589_Propagati...) - the difference is quite large for brick and cinder block; unfortunately, they didn't measure insulation foil, which I expect would be quite a good RF shield, especially if earthed.
So if everyone switched to 5 GHz, the interference situation might still be better than if everyone was on 2.4 GHz.
Of course, being an early adopter of 5GHz probably helps with the other problem in apartment buildings, the 'prisoners dilemma' type problem where everyone who knows how ups their transmit power because of the noise, making the problem worse for everyone else but temporarily better for them, when if everyone lowered their power, everyone would get better speeds (exactly analogous to how everyone ends up shouting when having a conversation with the person next to them at a party, when if everyone talked quietly instead communication would be more successful).
Increase the beacon period of your router/AP to the fastest it will go, usually 20 microseconds. I think this is the best solution of anything you could try.
Maybe play around with the DTIM interval but I'm not sure what a good number for that is; too low supposedly drains batteries of wireless devices and too high causes other problems.
Max out RTS/CTS but you may lose overall throughput but that's no loss if it suck already, in for a lamb in for a sheep.
There are other settings too most explained in the help section of the AP/router help menu. They can be obscure but fiddling with them can help your AP signal a lot.
That's my unofficial educated guess theory.
The best bet it to switch to 5GHz, but that isn't practical for use with mobile devices.
Option B is to turn off the higher speed modes like 802.11n. Just try to stick with 11g. If you are still having connection problems, maybe switch down to 11b, but that will be real slow even when it works.
If you use an access point with detatchable antennas (which is actually most of them if you open the cover), then maybe replace the omni-directional antenna with a high-gain directional antenna (also known as a patch antenna). Then you'll need to point the antenna at where you sit.
Another (probably lousy) option to try (but very quick and cheap) is to move off of the commonly used WiFi channels (1, 6, 11). They are commonly used because they don't overlap with each other. So maybe try 4 or 9. The downside is that you will get interference from two commonly used channels, but the overall situation may be better than what you've got now.
You say "switch to 5GHz, but that isn't practical for use with mobile devices" -- is the reasoning that the 5GHz signal doesn't penetrate the walls enough as you walk around with the device?
Although I do agree with your advice about channels I often get relatives to do that as they first step in troubleshooting problems with their home wireless network.
People have all those adjustable router options they may as well try something rather than default settings. You don't have to design wireless devices for a living to fiddle with a few settings.
Note that in most cases wireless systems are far slower than theoretical speed, but 100Mbit wired ethernet is good for 90+ in both directions simultaneously, so in most cases it'll be faster than 802.11n, and with better and more consistent latency.
Take away "in many conditions" and replace with "always, without exception" and replace "faster" with a "at least a magnitude faster" and we are in agreement.
If you need performance and reliability (like for instance for iScsi) there is really nothing which even compares to wired ethernet.
The short version is that, depending on your usage, you may run out of NVRAM before RAM and may lose your settings. For reference see [1] and [2].
[1] http://www.dd-wrt.com/wiki/index.php/Asus_RT-N16#Current_Kno... [2] http://www.dd-wrt.com/phpBB2/viewtopic.php?p=506126
I have 32MB NVRAM to play with and that has served me well enough, but I see plenty of consumer-routers which can be "upgraded to dd-wrt" but which doesn't even have enough NVRAM to do an ipkg update.