A CNC requires specialised skill. Downloading and printing 3d doesn't.
Building guns with a CNC requires a lot of labour. Whereas you can imagine having a lab full of 3d printers being operated by a single pensioner.
3d printers look like they'll be generic and mass-produced. If so, in ten years there will be 3d printers everywhere. People sitting in refugee camps on the edge of hotzones won't have have difficulty getting access to them. At some time in the near future there will be a good-enough equivalent to the assault rifle that can be 3d printed. And drones. And other things.
The US has avoided pouring arms into Syria partly out of concern for the mess that it will leave behind afterwards. Also, they're wanting to avoid arming people hostile to the west. These arguments are valid now, but we can see the end of it.
Now if you can 3d-print a reliable rifle like an AK-47, that could get interesting.
Now if you can 3d-print a reliable rifle like an AK-47,
that could get interesting.
The team that made this gun are already doing the most difficult bit from the AR-15, a semi-automatic rifle that has been used in several massacres in the west (including the one that sparked heavy gun regulation in Australia in the 90s).That's why I thought this was news. First they made the lower-receiver of a powerful gun. Now they've also succeeded in producing all the parts of a not-powerful gun. As I see it, they've got a piece of string over the chasm and will iterate from here to build a bridge.
I expect the barrel will be difficult (need a big machine and the rifling is probably tricky as you get to the top). The gas-reloading mechanism will take some work. But the lower-receiver is where most of the pressures where you might have doubt that plastic would work, and that's the bit they've already done.
And that's just reimplementing an existing gun with a design that was optimised for metalwork. After that we'll see a bunch of development in designs that are optimised for plastics and printing. That'll be your AK-47 equivalent.
As far as I understand it, the lower receiver on an AR-15 is actually a pretty trivial housing component, subject to almost no operational pressures, but interesting legally because it's where the gun's serial number happens to be stamped. (But I should note I don't really know much about AR-15s, just stuff I've read.)
I am sorry but really - people in a refugee camp, with no sanitation, insufficient food and clean water, and yet working 3D printers with plentiful supplies of plastic dust?
Refugee camps are by defintion, walkable from the worlds worst trouble spots, Access to weapons in the worlds worst trouble spots is not hard (http://www.the-star.co.ke/news/article-43343/police-recover-...).
3d printing of guns is a "first world problem" and will remain so forever. By the time a refugee camp has turned into a place that worries about 3d printing of anything, it has become a suburban utopia and the soccer mums can deal with the 3d printing labs.
So, while I agree that 3D Printing of guns is likely, for the near future to be a "First world problem" - I don't think I would make that prediction 30 years out, and certainly would never be so bold to say "Forever". I can certainly see a future in which Refugee Camps don't have Water, Food, or Sanitation, but do have a broad array of 3D Printers and base printing material.
The newness comes from being able to have an unskilled user setup a 3d printer, buy some ABS plastic to feed into it, download a file from the internet and begin producing guns. I don't know if this is a good or bad thing, but it's something to watch carefully.
I could imagine a future where it's almost like the wild west again, so many people who would harm you have guns that everyone carries one in a holster, and it's just considered normal, like wearing a sword all the time was normal for the samurai. This may end up being a likely future in the USA since the 2nd amendment is impossible to repeal.
Anyone who can afford a 3D printer and the material can already afford a cheap rifle that will work infinitely better.
extremely detailed paper: http://www.smallarmssurvey.org/fileadmin/docs/B-Occasional-p...
for something a little less dry and with pics of the guns see: http://www.vice.com/read/port-moresbys-little-raskols
the 3d printer angle is interesting from a tec perspective, but i cant help feel that this is more about a guy building himself in to the linus of guns then gun policy.
Convenience turns out to be a pretty big contributing factor in how many people do something!
This is anti-American propaganda. All those mass shooters, they would have just found another way.
My uncle built a similar cannon from some pipe and shot holes through sheet metal with it.