6,092 karma · joined October 29, 2013
Likewise, level 2.12 is a bit messed up, given you can ignore BitLineBar. I'm not sure what the intended solution was.
Most brass instruments have three valves. The first lowers the pitch by a tone. The second lowers the pitch by a semitone. The third lowers the pitch by a tone and a half. If you need to lower the pitch by two tones, then you press the second and third valves at the same time, and that works fine. However, if you need to lower the pitch by three tones, then you need to press all three valves at the same time. However, that adds the length of all the valve loops together to the total length of the instrument, whereas to lower the pitch by a fixed interval you need to multiply the length of the instrument by a certain amount, and so to truly lower the pitch by three tones you need to add a little bit more length beyond that supplied by pressing all three valves together. That's what the finger loop on the tubing for the third valve is for, so you can slide it out a bit for certain low notes.
It is a cultural problem. Just paying a bit more won't fix it. By paying a bit more, you might be able to get a larger share of the limited portion of people in the society that care, but you're not changing the people fundamentally, just being more selective.
Following distance is the rule that you should leave a 2 second gap in front of you. That is often less distance than the braking distance.
You should be always able to see that your braking distance is or will be clear, and that sets the maximum speed you should drive at as you approach areas with reduced visibility, like corners or the brow of a hill. You must learn braking distances for the driving test.
This assumption is untrue at very low speeds, particularly when it takes longer than 2 seconds for a car to pass a point. For instance if we assume cars are 4m long, then with an interval of 2 seconds the cars would be touching at 4.47mph
The assumption is also untrue at very high speeds. You'll want a larger gap. That's partly because at such high speeds the ability of a vehicle to decelerate differs - if a vehicle with good brakes does an emergency stop and the car behind it has a respectable 2 second gap but has worse brakes then they can end up colliding. It's also partly because a 2 second gap at very high speeds means the car in front is further away, and that can cause a greater delay before the driver realises what is happening. As a third reason a greater margin needs to be used at very high speeds simply because the consequences of a crash are that much greater and should therefore be avoided even more than at lower speeds.
Therefore there is a kind of U-shaped curve in the "safe" following interval, and consequently a speed at which safe throughput is maximised.
That's why variable speed limits have been introduced in various places. For instance, in the UK which normally has a 70mph speed limit on motorways, in very high traffic conditions this can be lowered using electronic signs to increase the safe throughput of the road. It's commonly reduced to 50mph, though it does get lowered further in sections approaching a queue of vehicles that has actually stopped.
There's also the issue of speed oscillations. With a high speed limit and vehicles following too closely, a little variation in speed in one vehicle can turn into a larger variation in the following vehicles, causing a backwards-travelling wave of braking (sometimes to an absolute halt) and speeding up again. Lowering the speed limit reduces this.
I recommended that the journal not publish the paper, and gave them a good list of improvements to give to the authors that should be made before re-submitting. The journal agreed with me, and rejected the paper.
A couple of months later, I saw it had been published unchanged in a different journal. It wasn't even a lower-quality journal, if I recall the impact factor was actually higher than the original one.
I despair of the scientific process.
I had a similar situation with SMS messages that were being sent to me with links informing me of status updates. These texts were useful, and I would go over to my real computer to check the web site. Then after a few days the text messages said "It looks like these messages aren't getting through to you, so we'll stop sending them." Which is also stupid, but it works for most people that load the web site on their phone from the SMS link. God help you if you have a dumb-phone.