And when it isn't as hot out, you can actually use the ground temp to radiate heat out of the house by itself, no need for coils and a fan to run in ambient air temp, right?
And when it isn't as hot out, you can actually use the ground temp to radiate heat out of the house by itself, no need for coils and a fan to run in ambient air temp, right?
For a home aircon it might be OK, however the London Tube is having serious problems with this where many of the tube tunnels have warmed from around 14C to nearly 30C (57-86F) over the last 100 years. Leaving many of them quite hot. The surrounding ground around the tubes has warmed up and effectively heat soaked.
Heat is generated from a number of sources including diesel engines however apparently a large portion of the heat is generated by braking for each station. They've improved that by using electric regenerative braking now which in some cases can dump the power into other trains that are accelerating at the same time.
Some of the newer trains now also have air conditioning inside the trains, while that helps inside the train it doesn't help outside the train where even more heat is dumped.
Anyway for more information there is a good youtube video I can't find right now, so you could read this instead: https://www.forbes.com/sites/lauriewinkless/2017/06/22/sweat... https://www.ianvisits.co.uk/blog/2017/06/10/cooling-the-tube... https://en.wikipedia.org/wiki/London_Underground_cooling
The other day, when it was 106F outside and I had to dry some clothes, I found it quite unfortunate that I was spending a bunch of energy to move hot air out of my house, while at the same time spending a bunch of energy creating hot air in my house to dry my clothes.
It would have been so nice if there were a reasonable way for me to take the heat already in my house and push it through the dryer.
(I could have hung them to dry, but I live too close to the freeway to do that -- they would have been dirtier than when I washed them)
In the US, but have been running Bosch condensation dryers for over a decade. Previous rental had one and the immediate difference I noticed was how much longer my clothes lasted from the cooler temps, so when I moved I bought my own W/D. No regrets.
Of course, only works for electric!
http://www.greenbuildingadvisor.com/blogs/dept/guest-blogs/h...
Also worth noting that dryers usually vent outdoors so they don't dump all the heat inside, where you'd then have to use the AC to remove it.
[1]: https://water.usgs.gov/edu/qa-home-percapita.html
[2]: http://www.awwa.org/portals/0/files/resources/water%20knowle...
(2,842 cubic meters in liters)/365 = 7.7k liters.
The USGS [0] estimates 23,800 mega-gallons per day for domestic use by 268 million people. This is about 89 gallons or 336 liters per day per person.
For example:
Meat consumption accounts for 30 percent of the American figure, and sugar consumption is responsible for another 15 percent
https://www.scientificamerican.com/article/graphic-science-h...
> Similar to a geo-exchange (or geothermal) system, heat pumps transfer thermal energy from the warm sewage supply to a higher temperature range that’s effective for residential space heating and domestic hot water. While similar in concept, sewage heat recovery is more efficient and cost effective than typical geo-exchange systems. The heat source (raw sewage) has a higher temperature than ground-source heat (on average 18 degrees Celsius as opposed to 8), so it requires less energy to upgrade. Secondly, accessing the sewer line is less invasive and less capital cost intensive than drilling into the earth to access geothermal heat. It also utilizes a continuous supply of waste heat, closing the loop on a fundamental energy >> waste >> energy stream. [2]
[1] http://greenbuildingaudiotour.com/buildings/sefc_neighbourho...
[2] http://www.thechallengeseries.ca/chapter-05/neighbourhood-en...
I was only thinking of it in context of using the ground to sink heat, not as a real implementable plan. I think it goes without saying that the heat-pump-as-a-water-heater idea is far more pragmatic.
There are other systems for people with the land which may be less expensive which don't require drilling.
I spent several summers installing these systems, they are surprisingly simple and effective.
Power plants and ACs are not 100% efficient; the power plant converts chemical/nuclear/mechanical energy into electrical energy, releasing heat from work lost.
Your AC will convert electrical energy to cool the air around you, but because it is not 100% efficient, the total temperature of the system will rise.
There needs to be a way to get rid of that lost energy and remove it from the system. If you put that into the ground, it's still in the system. Ofc, even when they try to 'beam the heat to space', much of it will end up staying in the system (earth) as it reflects on clouds / water vapor, etc.
This is the main reason why it suddenly gets so cold at night. From a radiative perspective, you might as well be facing a ceiling of Arctic ice above you.
I'm an amateur astronomer. When I do observations at night, I always add an extra layer of clothing. It's amazing just how really cold it gets when all you do is sit under the clear night sky.
When it's cloudy it's different. The chill effect due to the (lack of) radiation is much less intense.
Source: https://www.forbes.com/forbes/welcome/?toURL=https://www.for...
> According to this article in Rail Magazine, the average temperature inside the tunnels was around 14° in 1900.
> increased the temperature of the surrounding clay so much that, today, average tunnel temperatures are between 20-25°C.
There are limits to the technology. Skyscrapers are simply too large for any reasonable number of wells to provide adequate heating and cooling, Mr. Orio said. And it would be very difficult to install a well beneath an existing structure.
http://www.nytimes.com/1997/04/20/nyregion/new-building-will...
http://geothermal.boschprohvac.com/site/geothermal-explained...
https://www.google.com/search?q=geothermal+price
---
a typical home of 2500 square feet, with a heating load of 60,000 BTU and a cooling load of 60,000 BTU will cost between $20,000 to $25,000 to install.
---