957 karma · joined June 14, 2021
Satellite photography/sensing vs Airplane based vs UAV based vs local vs point detection.
The higher the altitude of your sensor, the larger the swath of land you can sense, but with height comes tradeoffs... cost, weather, satellite availability, latency/how often the satellite is going to be over where you want to sense just to name a few.
Closer to or on the ground means you can get pinpoint accuracy but that comes with increasing cost of labor. Think cost of an airplane or UAV pilot vs an individual walking around with a methane sensor sniffing around flanges, valve stems, etc.
The different approaches are somewhat complimentary. Satellite can you tell you've got a problem area. You can then deploy people on the ground to "zoom in", but if you're operating a ton of sites, you wouldn't start on the ground.
https://www.ncbi.nlm.nih.gov/pmc/articles/PMC2769828/#:~:tex....
https://techhq.com/2023/12/why-was-singapore-central-to-nvid...
Reasons for wtf:
- SG in terms of datacenter load in megawatts is a fraction compared to the US. Approx 900ish MW in SG vs 19000 in US. Where are all those GPUs going?
- There's been a shortage of rack space in Singapore due to high demand AND lack of supply due to A.) singapore is tiny, B.) there was a moratorium on new builds. Again, where are all those GPUs going to fit in SG?
- Assuming new GPUs are going into the DCs, presumably that would mean the DCs are having to be retooled to handle higher density rack loads.
I suspect that a lot of those GPUs were purchased in SG and shipped to China. The only other way I could reconcile those numbers is if someone were purchasing the chips and manufacturing cards in SG.
They'd also target our trucks to get any stored wire, tubing, fittings, or power tools they could get their hands on.
Viewed through the lens of Broken Window Theory, perhaps people are more brazen given the current state of SF.
Author suggests applying a new manufacturing technology, 3d printing, to help alleviate a supply shortage, but then says new mfg tech probably wont work (I'm inferring that it will not work with the existing design).
I'm proposing an alternative - make a 3d printer friendly design (OK, it may not be as good as the legacy version) but you're able to build the munition in plants that can be repurposed as soon as the "peak demand" goes away.
No rounds seems like a worse condition than having equal-or-poorer performing rounds.
The landmass of Singapore itself has grown by 40% since the 60's through reclamation. There's always been lots of rumors about how the sand was sourced from neighboring countries.
https://thehill.com/policy/international/4423913-state-dept-...
AFAICT, there were no readily obvious DP sensors to be found.
The machine can know if it measures differential pressure across the filter. If the DP across the filter is too high (indicating a clogged filter), the filter needs to be replaced.
Hypothetically, yes, there's a perverse incentive, but is that what is actually happening?
A clogged filter can stress the fan motor which can A) increase power consumption and B)reduce overall product life.
I wouldn't say it's crazy. When buying industrial equipment, it's commonplace to have a Factory Acceptance Test (FAT) where engineers from the customer travel to the supplier factory to verify everything is built to spec and functions as expected. Upon passing FAT, equipment is shipped to site and installed where it then undergoes a site acceptance test (SAT). After SAT, the equipment is "handed over" to the client. The FAT-SAT process can be applied to anything from small individual pieces of equipment all the way up to huge skids/packages.
In shipbuilding, classification agencies like ABS or DNV have inspectors that monitor the construction of a ship.
A lot of countries have minority shareholder rights. This seems like something where those rights would kick in (even if you just have options).
Manufacturing tooling and test jigs
A quality management system
Support and RMA systems
PLM software although you could probably get away with excel for a while
> UL certification / FCC
A lot of other certs if you want to sell into overseas markets... Luckily the US market is pretty big
I strongly recommend you hire professionals for this. I've worked as a Product Manager for physical products. There is a gulf of knowledge between designing something in CAD and designing something that will endure the rigors of toasting for 20 years. The previous sentence doesn't even cover the gulf of knowledge between taking a prototype to a design that's meant for mass production.
I'm interested in creating a portfolio of open source appliances. Stuff that will last for life (or is at least repairable). If it's a "smart" applicance and open source, you don't need to worry about your appliance spying on you or being at the whims of a vendor who bricks your device for whatever reason.
The above example comes from a colleague who used to work in the SSD business.
VFDs are connected to the process control system through a variety of interfaces... simple voltage or current loops, serial buses like BACnet, modbus, or ethernet interfaces like modbus TCP.
I'd add a few things:
- Heat pumps have been around a while. In the southern US, there are lot of older HVAC techs with a negative perception of HPs based on problems with older technology. Older HPs had less of an ambient operating temperature range, in which case the emergency heat would activate, reducing savings.
- Re: fragmented markets, different states/cities/towns/municipalities have different rules, processes, procedures, etc.
- Re: the desire for drop-in installations, the construction permitting and inspection process is a big fat roadblock which is linked to the problem above.