10,977 karma · joined May 14, 2014
Are they objectively good? No. Do they regularly fail, cause fires, or shock people? No.
Even my kids when young understood how to grip the plug without touching the metal contacts and to this day still have not been shocked. In theory can something fall and hit the pins just right to cause a short? Sure. You could also get struck by lightning. In practice it just doesn't happen very often.
For the US/North American NEMA style there are some improvements and some clever things about them. Modern receptacles have shutter doors that stop you from putting anything into the holes unless the ground pin or neutral pin unlocks it first. Many plugs also cover the rear part of the hot/neutral with plastic so if the plug is not fully inserted there is no exposed metal.
The plugs also prevent mixing voltage and amperage. The typical two vertical blades (5-15) are for 15 amp circuits. 20 amp circuits (5-20) have one horizontal + one vertical blade. The receptacle has a T shaped slot to match - that way you can plug a low-amp device into a high-amp circuit but not the reverse.
Similarly the 240v version of this plug (6-15/6-20) has the same property: 15amp and 20amp versions. The 15 amp is two horizontal blades. The 20 amp is one horizontal + 1 vertical but swapped places compared to the 120v version. I do wish more builders installed the 240v receptacles in kitchens in the US. There is no technical reason we can't have higher power kettles and whatnot. If code required these in garages and kitchens more appliances would be available for them.
(I find it insane that Brazil continues to be dual exclusive voltage; all of North America is dual concurrent voltage. Every home/office has 120v and 240v available. In Brazil it depends on what state/city you live in - some get 120v, some get 240v. Even worse they use the same standard plug design for both so you'd better hope the plug is the right color or has the right sticker. And you can't be sure you can take electrical appliances from one city to the next! At least they should have adopted different plugs for different voltages.)
The huge advantage of these plugs is compatibility. We already have them. The cost to change designs is massive. The benefit extremely small. It just isn't worth doing.
Note: The 240v NEMA plugs I am referencing are not "dryer plugs" which are physically much* larger and designed for much higher amp loads in the 30-60 range. The 6-15/6-20 are literally identical to the standard 120v plugs but with different blade orientations. They were designed to support 240v appliances in everyday use since all of North America is dual voltage. In practice 240v is only ever used for large appliances like ovens so the 6 series doesn't get much use which is a bit of a shame.
:)
Want a desk fan? There are four types of desk fan in the entire world (per Amazon). Page after page after page of listings of the exact same four designs. Often listed with the same re-used marketing artwork.
Put aside brands, quality, et al. Put aside the fact that Amazon removed almost all product specs from their search facility (and is increasingly deleting specs entirely from product pages). Put aside the fake reviews, no-name Chinese drop-shippers.
Every category is stuffed full of the same few copycat products over and over. It is extremely difficult to merely find actual choices! Wrenches? Small compartment storage boxes? Paper towel holders? If you can find even 20-30 unique products in a category now you're living like a king. It reminds me of AliExpress in that sense. Lack of specs, lack of manuals, lack of details about any product. The same listings from different no-name stores repeated over and over.
I used to think maybe AliExpress & co were actually good if you spoke Chinese but a Chinese coworker kindly informed me that nope, it is just as horrible for everyone living in China using Chinese.
I don't know where we went wrong but this is not the future we were promised. Can any of you remember when Amazon was actually good? When their search was useful? Those were some amazing times and how little did we realize they were fleeting.
None of those cities are saving money or even _planning_ for the inevitable repaving, pipe re-lining, etc. Worse: many of them were built up in waves so much of the city's infrastructure will "come due" around the same time.
I never imagined we would see San Francisco (of all places) overhaul its permit process. I can now build a deck in my backyard, add a story to my house, or build an ADU without having to pay DBI to send certified letters to all my neighbors asking if they'd like to object, then being forced in front of the planning commission when they do so. That's a direct result of the pro-housing legislation at the state level, something Wiener has been heavily involved in.
It still highlights the performative nature of some legislation. I'm certain everyone involved understood that's exactly what would happen.
1. Rich cheats for whom complexity is the goal. Reduced enforcement benefits them without the guilt. They can construct nonsensical schemes but if no one ever audits them they get to feel like they are paying what they owe despite being freeloaders.
2. Strangle the baby types: they hate the federal government. They deliberately want to reduce its income to force cuts to government spending (programs and staff). If they can they will cut other parts of the government then use that to justify reducing taxes. Nothing else matters except shrinking the federal government as much as possible via any means possible. These types also enjoy taking any government service that works and people like and making it as terrible as possible to kill popular support thus making it easier to cut the program entirely.
When I eventually got it to issue a refund I realized they kept the service fees and driver tip. For an order I didn't even receive!
If that's the best they can do I'll just go pick it up myself.
I'm not sure even one such machine exists. Some companies market benchtop or small lathes as "gun lathes" but that is marketing fluff not a technical description. Any lathe can be used to make weapons. They have tons of round parts and parts with drilled holes. So does everything else that gets manufactured.
I am not aware of any machine tool company that manufactures lathes, mills, etc explicitly designed just for manufacturing firearms.
So in that sense the law you reference is typical of performative legislation. You have angry idiots pestering you to Do Something(TM). So you pass a do-nothing bill. You get to say you banned a thing that never existed. Meanwhile it doesn't hurt or bother anyone because it applies to no one. That's the best of both worlds! Do nothing while looking busy! Take action without actually hurting anyone.
Is it silly? Yes. But I'd rather they do stuff like that then actually try to regulate 3d printers.
No one built a business by starting out with huge email blasts. At least not anytime recently.
You start by finding individuals and addressing them as individuals. When you find one such person who finds your product extremely useful they will often generate leads for you to others who need to solve the same problem. Keep doing that high-touch direct contact.
In other words: sow the seeds.
Highly unlikely as the feedback cycle used to train LLMs will choke off all future learning.
In other words if AI bots consume and regurgitate everything you publish on the internet what is the incentive to publish anything? No one will read it except the bots. The training datasets will either become stale (no longer learning anything new because nothing new and useful is published) or actively poisoned (because only bad actors will bother to publish).
And the generation constantly fed mostly correct information by AI will implicitly trust it further making poisoning of the models a high-value target.
Very few people will be left who understand how to think and have the motivation to do so. Even fewer will have the motivation and the means to publish to others.
K-12 spending: the same dilemma afflicting everywhere. Despite spending more dollars not getting an equivalent return. Yet teachers are not raking it in. The money is disappearing somewhere. Is it similar to university level: top-heavy administration? Excessive spending on facilities?
I don't know where these estimates are coming from. They seem high. Sometimes an investment in services pays off long-term. CA's cuts to early childhood services only ends up with a bigger bill down the road as more kids fall off and end up either needing help later or getting into trouble.
But I agree with you: in all these areas how much are we spending, in adjusted dollars, per beneficiary and what are the outcomes? If possible how much "overhead" exists in each program? I suspect there is a lot of fat to be trimmed in these areas as admin/management gobbles up bigger slices of the pie while delivering nothing of value. You can see this writ small in San Francisco housing programs. Quite a number of non-profits that claim to be about housing, sucking up funding, then a) opposing all new housing where they don't get to wet their beak b) not actually putting a single person in a home.
Evolution is just super super messy.
Many states have a statute of limitations anyway. If you live on the land and pay the property taxes for N years everything else becomes irrelevant. Either the title was transferred to you or you squatted on abandoned land for N years: in both cases it becomes yours.
WD-40 is great for machining aluminum, cleaning grease/other oils, and if you want a mild temporary lubricant not something that will make a massive mess or irritate your skin.
So a clock doesn't solve the problem. The amount of data sent on each clock pulse also tells you something about what was sent.
The Chaff packets already fire on a timer. They inject random extra fake keystrokes so you can't tell how many keystrokes were actually made. The only other way I can think of to solve that is by using a step function: Send one larger packet (fragmented or the same number of individual packets) on each clock pulse if the actual data is less than some N where N is the maximum keystrokes ever recorded with some margin. Effectively almost every clock pulse will be one packet (or set of packets) of identical size. Of course if you do that then you'll end up consuming more data over time than sending random amounts of packets.
GPU is a function of limited manufacturers and vendor lock-in combined with massive capex required to compete(). Like some (but not all) price inflation during and post COVID: rising prices can become a self-fulfilling prophecy. If all your customers expect prices to rise might as well meet their expectations and get while the gettin' is good.
() Like a new CPU architecture only worse. The amount of engineering required as "table stakes" increases exponentially while at the same time the manufacturing expertise does the same. This suddenly and rapidly raises the barrier to entry. Anyone who can survive the early squeeze can do quite well in such markets.
Then again... they did try to force VLIW and APX on us so Intel has a history of "interesting" ideas about processor design.
edit: You addressed it in the article and I guess that's probably the reason but for real... what a ridiculous hand-wavy thing to do. Just assume it will be fine? If the anecdotes about Itanium/VLIW are true they committed the same sin on that project: some simulations with 50 instructions were the (claimed) basis for that fiasco. Methinks cutting AMD out of the market might have been the real reason but I have no proof for that.
A machine shop should connect 1/3 of their lights to each phase so it is immediately obvious if a phase gets dropped. Lots of equipment will suffer on two of three phases but with lower performance or even damage.
That's definitely possible but I think the cause is much simpler: initially they wanted to bootstrap their own industries and now nothing forces them to do anything different so they just continue with hyper-protectionist policies.
On the side of the west: Outsourcing to China is the new group-think. The new "No one ever got fired for buying IBM" for the MBAs. A box of Bandaids now says "made in china" on it. Bandaids are churned out entirely by machine. Packed entirely by machine. Boxed entirely by machine. By the millions per day. Human labor input is more or less irrelevant. Why outsource that to China? Because that's the only thing management knows how to do and the only thing so-called investors understand. It certainly isn't to save money or make the product better.
> However China wouldn't benefit if their customers are poor.
If I had a nickel for every time a government or leader adopts bad policies despite the obvious future negative consequences I'd be the world's richest person.
Funimation lowered the bar so much I thought it couldn't go lower.
Who knew HiDive would prove me wrong.
Citation needed.
In the early days of autopilot/FSD most of the fatalities were people doing stupid things like watching a movie or sleeping in the back seat. That's why it now has to monitor your face with a camera to detect whether or not you are watching the road - to stop people from being idiots.
However we must acknowledge that any change in the automotive space is going to lead to problems and some percentage of those are going to cause injuries. That is the nature of cars. They do not have the certification standards of aircraft nor the training of pilots. They can't and they won't.
It is also inevitable that autonomous driving is going to make different mistakes than a person would make. On a miles-driven basis it still produces fewer accidents and injuries than human drivers.
The west and the US specifically has operated on an open market policy partly as a result of two world wars we got dragged into in relatively short order. Economic integration was thought to reduce the likelihood of another great war.
However what we have currently is a relatively developed economy (China) using currency manipulation and protective policies to prop up their own economy long after it has passed out of the "developing" phase. Plus massive and ongoing state investment and debt deferral. China effectively subsidizes massive amounts of economic activity that makes any US or EU tax breaks / protective policies look like chump change.
When you have such a large market participant behaving that way it is little wonder that people lose their faith in free markets and want to intervene. Including doing explicitly punitive things against China. It is an attitude of China's own making. After all... China will not allow you to buy a freakin' popsicle stand as a foreigner let alone a shipbuilding company or anything else.
China wants all the access to the rest of the world and wants everyone to buy their products... but they do not want to reciprocate.
Back when they had software developers they were rapidly improving the app but someone decided they needed more executive bonuses and laid everyone off. Their software hasn't moved an inch since.
Funimation had the same idea. They bailed out of VRV (Crunchyroll's attempt at an anime "marketplace" all-in-one app) and released their own garbage app that is somehow much much worse.
It is the classic "we have exclusives so these drooling morons will take whatever we deign to give them because we're the only ones with show X/Y/Z" move.
Remember orbit is not like a flying airplane. Those things are going so fast friction forms a plasma that eats away at the object as it decelerates. If you can expose more surface area that effect will eat away at much more of the object. So you design it to have through-bolts or other fastener designs where the outermost portion of the fastener burns off quickly, allowing the whole assembly to rapidly disassemble and vastly increase surface area.
If it were me I'd assume the majority of BMC firmware out there from all vendors: 1. Is full of many many exploitable vulnerabilities 2. To the extent they patch holes it will be whack-a-mole because the economics do not permit large investments in software quality. 3. Many server owners will never install a patch anyway.